One Arm Endless Bowstring Jig
Here's the scoop on how to build a cheap and simple one arm endless bowstring jig. First, why one arm instead of the traditional two? Because you don't really need two! One arm allows for a simpler jig that will build a string just as quickly and accurately as a two arm jig. I've been using a One Arm Endless Jig for well over 10 years - it works extremely well.


Materials (all acquired from Home Depot)
main beam - (2) 1-1/2"x72" slotted metal angles (zinc coated) (Note: you can use 1/8" 1-1/2" aluminum angles as well, but they're much more expensive and you need metal cutting drill bits to make the required five 1/4" holes)
arm, beam separators, feet - (1) 2x4x72" fir - get one as blemish free and straight as possible
string posts - (2) 3/4" diameter birch dowel - 18" minimum - get one as straight as an arrow!
arm foot - (1) 1"x5"x7" - any kinda scrap wood that's between 3/4" and 1" thick
beam fasteners - (5) 1/4"x2-1/2" bolts, nuts and washers
wood fasteners - (8) 2-1/2" dry wall screws
main arm pivot - (1) 1/2"x5" carriage bolt, 1/2" wing nut, large washer
string trees - (3) #10x2-1/2" (or thereabouts) flat head wood screws
string tie-down - (1) 5/16"x2" wall hanger screw and 5/16" wingnut, 2 washers
string post lashing - some strong unwaxed thread
glue - 5 minute epoxy to fasten in the string posts

Tools
Cutting the 2x4 - table saw or circular saw or jig saw or hand saw
Drilling the holes - electric drill and 3/16", 1/4", 1/2" and 3/4" wood bits
Tighten the bolts - box wrenches and/or vise grips
Wood screws - a 1/16" drill bit for pilot holes is nice, screw gun, screwdriver

Please Note: If you don't know it, a 2x4 is really 1-1/2"x3-1/2"!
Wherever "2x4" is mentioned, those sizes prevail!

Building the Jig

Please Note: The full length 72" slotted angle beams will make a jig that will build a bowstring as long as 76".   If your maximum string length requirements are less, you can cut shorten both metal beams by cutting with a hacksaw.

* Measure off and cut the 2x4 for ...
one 18" length (for the arm)
one 9" length (for the single post end)
one 7" length (for the arm support)
one 3" length (for the end piece)
two 4-1/2" lengths (for the feet)

* You'll need to cut the 2x4x7" long main arm support lengthwise, to provide a 1-1/2" thick, 1-1/4" wide, 7" long piece of wood ...

See it, nestled between the pair of slotted angle main beams.

* Take the 9" length and put it between the angle beams, at one end - drill and secure with three 1/4"x2-1/2" bolts - make sure the bottom of the 9" length is flush with the bottom of the angle beams. After securing, add a 4-1/2" foot to the bottom of the 9" length with the drywall screws ...


* You'll need to cut the 2x4x3" long length lengthwise, to provide a 1-1/2" thick, 1-1/4" wide, 3" long piece of wood. Take that 3" length and put it between the angle beams, at the other end - drill and secure with two 1/4"x2-1/2" bolts - make sure the bottom of the 3" length is flush with the bottom of the angle beams. After securing, screw in a 4-1/2" foot to the bottom of the 3" length with the drywall screws...


* Take the 1"x5"x7" piece of scrap wood and fasten it to the bottom of the 7" length arm support, using drywall screws ...


* Take the 18" length that's the main arm, mark the exact center of the 4" wide side and drill a 1/2" hole completely through (see above pic).

* About 1" from the end of the main arm support, drill a 1/2" hole completely through and insert the 1/2"x5" carriage bolt (see above pic).

* Centered about 1" from from each end of the main arm, drill a 3/4" hole as straight in as you can - it must go at least 1" deep, but could also go completely through the 2x4 ...


* Glue a length of 3/4" dowel into each main arm string post hole - bottom out the the dowel and cut off enough so that 4-1/2" remains above the top of the 2x4 (see above pic).

* Centered about 1" from the end of the 9" length arm support, drill a 3/4" hole as straight in as you can - it must go at least 1-1/2" deep, but could go deeper ...


* Glue a length of 3/4" dowel into each main arm string post hole - bottom out the the dowel and cut off enough so that 4" remains above the top of the 2x4 (see above pic).

* Centered, and off to one side of one end of the main, drill a 1/4" pilot hole for the 5/16" wall hanger. Screw in the wall hanger, add a few washers and screw on the 5/16" wing nut ...


* Assemble the main arm - use the 1/2" wing nut and a large washer ...


* Next up is drilling pilot holes in the ends of all three string posts, screwing in the flathead string tree screws, binding the ends of the dowels with heavy thread or string, coating the thread/string with epoxy ...


* On the single end post, I added a small plastic tube, that has a lip on one end, to the screw string tree - this rotates and makes turning the strands around it a bit easier - it's not mandatory ...


* All done ...

All set to spin an endless bowstring!


Questions, comments - email Rob at rfd@rfd.cc

Back to the main page
Back to the Documents Index